Booting to UEFI (BIOS) from Windows 10 and 11 Tap the F2 key to enter System Setup when the Dell logo appears. If you have trouble entering Setup using this method, press F2 when the keyboard LEDs first flash. Try not to hold down the F2 key as this can sometimes be interpreted as a stuck key by the computer.
Contents
How do I get into the BIOS on a Dell?
To enter BIOS, you simply need to enter the correct key combination at the correct time.
- Turn on your Dell computer or reboot it.
- Press “F2” when the first screen appears.
- Use your arrow keys to navigate BIOS.
How do I get into the BIOS on a Dell Latitude?
Turn on or restart your system. When the Dell logo appears, perform the following action to enter the BIOS setup program: With keyboard — Tap F2 until the Entering BIOS setup message appears. To enter the Boot selection menu, tap F12.
How can I enter BIOS if F2 key is not working?
If the F2 prompt doesn’t appear on the screen, you might not know when you should press the F2 key.
- Go to Advanced > Boot > Boot Configuration.
- In the Boot Display Config pane: Enable POST Function Hotkeys Displayed. Enable Display F2 to Enter Setup.
- Press F10 to save and exit BIOS.
Where is TPM in Dell BIOS?
Enable the TPM Security Feature in the System Setup
When the message “Press
How do I get into BIOS on Dell XPS?
Turn on (or restart) your computer. During POST, when the DELL logo is displayed, watch for the F2 prompt to appear, and then press F2 immediately. NOTE: The F2 prompt indicates that the keyboard is initialized.
How do I get into BIOS setup?
In order to access BIOS on a Windows PC, you must press your BIOS key set by your manufacturer which could be F10, F2, F12, F1, or DEL. If your PC goes through its power on self-test startup too quickly, you can also enter BIOS through Windows 10’s advanced start menu recovery settings.
How do I get into Intel BIOS?
The BIOS setup program can be used to view and change the BIOS settings for the computer. To access the settings, press the F2 key after the Power-On Self-Test (POST) memory test begins and before the operating system boot starts.
How do I force BIOS in Windows 10?
How to enter the BIOS on a Windows 10 PC
- Navigate to Settings. You can get there by clicking the gear icon on the Start menu.
- Select Update & Security.
- Select Recovery from the left menu.
- Click Restart Now under Advanced startup.
- Click Troubleshoot.
- Click Advanced options.
- Select UEFI Firmware Settings.
- Click Restart.
How do I access TPM in BIOS?
Boot computer using F2 into the BIOS setup mode. Locate the “Security” option on the left and expand. Locate the “TPM” option nested under the “Security” setting. To enable the TPM settings you must check the box saying: “TPM Security” to enable the TPM hard drive security encryption.
How do I find my Dell TPM version?
You can verify if a system supports a TPM firmware update by visiting the Dell support site and looking under “Drivers & Downloads” for that model. TPM firmware updates will be listed under the “Security” category.
Why is TPM not showing in BIOS?
If TPM is not present, please try the following troubleshooting steps:Note: To make sure TPM is turned on, you must press F2 to enter System Setup. Then go to the Security section and check that TPM is set to On under the TPM security settings. If TPM is restored, continue with normal system operation.
Can’t access BIOS setup Windows 10?
Power down the machine, unplug it, wait 10 minutes. Reconnect it then boot the machine again then use the command for loading your BIOS.
Try this :
- Hold down Shift and turn off the system – do not let up until it is all the way off.
- Wait a minute or two.
- Hold down the Bios entry key (such as F2) and power on the system.
Why is my computer not booting up?
Common boot up issues are caused by the following: software that was installed incorrectly, driver corruption, an update that failed, abrupt power outage and the system did not shut down properly. Let’s not forget registry corruption or virus’ / malware infections that can completely mess up a computer’s boot sequence.
How do I get into BIOS?
Get ready to act quickly: You need to start the computer and press a key on the keyboard before the BIOS hands over control to Windows. You have only a few seconds to perform this step. On this PC, you’d press F2 to enter the BIOS setup menu. If you don’t catch it the first time, simply try again.
How do I change my BIOS from legacy to UEFI Dell?
You can resolve this issue by returning the system to the UEFI boot mode.
- From a power off state, power the system on and press F2 to boot into the BIOS setup menu.
- Select “Boot sequence”
- Change the option from “Legacy” to “UEFI”, then select “Apply” in the right lower corner.
What is legacy boot mode Dell?
Legacy Boot mode and internal boot devices
With the Boot option set to Legacy boot mode on newer series of Dell computers, you will be unable to boot to internal boot devices (including hard drive, SSD, or eMMC storage devices).
How do I enable TPM in Dell BIOS?
Resolution
- Click Apply and Exit to reboot.
- On reboot, tap the F2 key when the Dell logo appears to re-enter the BIOS.
- Expand the “Security” section, click “TPM Security”, and select TPM Security.
- Click Apply and Exit to reboot into the Operating System and enable BitLocker.
Does my Dell laptop have TPM?
How do I know that my computer has TPM 2.0? Dell computers that are shipped from 2015 onwards support TPM 2.0. You can verify this in the Windows device manager: Right-Click on the Windows Start Button.
How do I check my TPM in Windows 10?
To open it, press Windows+R to open a run dialog window. Type tpm. msc into it and press Enter to launch the tool. If you see information about the TPM in the PC—including a message at the bottom right corner of the window informing you which TPM specification version your chip supports—your PC does have a TPM.