Metric / Standard Wrench Conversion Chart
| Bolt Diameter | Metric | Standard |
|---|---|---|
| 1/8″ | 8mm | 5/16″ |
| 3/16″ | 10mm | 3/8″ |
| 1/4″ | 11mm | 7/16″ |
| 5/16″ | 13mm | 1/2″ |
Contents
What is the next size up from a 7/16 wrench?
Wrenches: Standard Combination Wrenches (1/4, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1)
Is 11 mm the same as 7 16?
11mm = almost 7/16 inch.14mm = almost 9/16 inch. 15mm = almost 19/32 inch. 16mm = 5/8 inch.
What size is 7 16th?
| MM | Approximate Size In Inches | Exact Size In Inches |
|---|---|---|
| 11mm | 7/16 Inch | 0.43307 Inches |
| 12mm | Just short of 1/2 Inch | 0.47244 Inches |
| 13mm | Little over 1/2 Inch | 0.51181 Inches |
| 14mm | 9/16 Inch | 0.55118 Inches |
What are socket sizes in order?
There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters). In-between sizes are available too, starting with 1/4 inch (0.6 centimeters) and increasing every sixteenth of an inch (0.16 centimeters).
How do I know what size wrench I need?
Multiply the first number which is the bolt size in inches or millimeters, by 1.5 using a pocket calculator, if necessary. For example, for the numbers in Step 1, 1/2 x 1.5 = . 75 or 3/4, which is the wrench size needed for this standard-sized bolt.
Will a 9/16 fit a 14mm?
But thats no biggie ~ to answer your question, 9/16 SAE is actually 14.3 Metric, but it is the closest SAE size that will fit a 14mm metric head.
How many mm is 7 16?
Conversion table inches to mm
| Dimensions — Inches to Metric | ||
|---|---|---|
| 0.438” | 7/16” | 11.13 mm |
| 0.500” | 1/2” | 12.70 mm |
| 0.563” | 9/16” | 14.30 mm |
| 0.625” | 5/8” | 15.88 mm |
How many mm means 1 inch?
25.4 millimeters
One inch is equal to 25.4 millimeters.
What is the decimal for 7 16?
0.4375
Answer: 7/16 as a decimal is equal to 0.4375.
What is 7 16th of an inch?
0.4375
The decimal equivalents of eights, sixteenths, thirty-seconds and sixty-fourths of an inch.
| Inches | |
|---|---|
| fractional | decimal |
| 5/16 | 0.3125 |
| 7/16 | 0.4375 |
| 9/16 | 0.5625 |
How many 64ths are in a 16th?
| Fractional / Decimal Conversion | ||
|---|---|---|
| 32nd | 64th | Decimal |
| 1/16 | 1/16 | 0.063 |
| 5/64 | 0.078 | |
| 3/32 | 0.094 |
What is 7/8 on a ruler?
The 1/8 of an inch marks are the smaller marks found directly in between the 1/4 of an inch marks on the ruler. Between 0 and 1 inch, there are marks that denote 1/8, 1/4 (or 2/8), 3/8, 1/2 (or 4/8), 5/8, 6/8 (or 3/4), 7/8, and 1 (or 8/8) of an inch. In total, there are 96 of these marks on a 12 inch ruler.
What is the smallest socket size?
Metric Socket Sizes Chart
| 3/8″ Drive | 1/4″ Drive | 3/4″ Drive |
|---|---|---|
| 8mm | 5.5mm | 22mm |
| 9mm | 6mm | 23mm |
| 10mm | 7mm | 24mm |
| 11mm | 8mm | 25mm |
How do I know my socket size?
How to Measure Socket Drive Size
- In the diagram above, the three key dimensions of a socket are labeled as Drive Hole, L, and S.
- L indicates the overall socket length.
- S indicates the target size of the nut, which determines which socket you’ll need.
- The size of the drive hole is determined by usage and torque demand.
What is the most common socket size?
⅜-inch drive size sockets are the most common and most available.
What size nut does a 7/16 wrench fit?
Hex Bolt, Lag Bolt, Square Bolt and Heavy Hex Bolt
| US Bolts | ||
|---|---|---|
| Bolt Diameter (in) | Head and Wrench Size (in) | |
| 3/8 | 9/16 | |
| 7/16 | 5/8 | |
| 1/2 | 3/4 | 7/8 |
What size head is on a 7/16 bolt?
Hex Bolt Head Size Chart
| Diameter | Head Size |
|---|---|
| 7/16″ | 5/8″ |
| 1/2″ | 3/4″ |
| 9/16″ | 13/16″ |
| 5/8″ | 15/16″ |
Will a 12 point socket fit a 6 point nut?
Compared with the 6-point socket, a 12-point socket has twice as many points, so it can more easily slide onto a hex nut. In other words, you would need to rotate only up to 30 degrees to fit a 12-point socket onto a hex nut.Torque power load is borne by the flanks of the nut or bolt instead of by the corners.
Is M14 bigger than 9 16?
The threads of an M14-2.0 screw, which is coarse, are spaced 0.079 inches (2.0 mm). A 9/16-12 screw, which is comparable in diameter and is also coarse, has its threads spaced 0.083 inches, which are farther apart, so there will be fewer threads per unit of measure (we used an inch in the table above).
What is equivalent to 22mm socket?
Metric / Standard Wrench Conversion Chart
| Bolt Diameter | Metric | Standard |
|---|---|---|
| 22mm | 7/8″ | |
| 5/8″ | 24mm | 15/16″ |
| 25mm | 1″ | |
| 3/4″ | 29mm | 1-1/8″ |