How To Setup My Dlink Router?

Follow these steps to set up your D-Link Router –

  1. Power on your D-Link Router.
  2. Connect your PC to the router using an Ethernet Cable or WiFi.
  3. A login page will appear.
  4. Now, you can configure and set up your router using the Internet Connection Setup Wizard.
  5. Under Wireless Setup enter SSID (WiFi Name) and Key (Password).

https://www.youtube.com/watch?v=Sw-uUaf1x-w

Contents

Why is my D-Link router not connecting to the Internet?

Ensure your Internet modem is connected to the WAN/Internet Port on the back of the D-Link Router. This port is typically Yellow.- Power Off your Internet Modem (Not the D-Link Router) for 20 seconds and then power it back on. Wait up to 2 minutes and check the Network Status again.

How do I configure my router?

In Android, settings menus vary from phone to phone, but once you find the Wi-Fi settings:

  1. Make sure your phone is connected to your router’s Wi-Fi network.
  2. Tap on the network name.
  3. Look for a ‘gateway’, ‘router’ or other entry in the list.

How do I know if my Dlink router is working?

Usually it’s http://192.168.0.1 or http://192.168.1.1).PressEnter.

  1. Type the username and password in the login page, the default username and password are both admin.
  2. Select the diagnostic tool: Ping.
  3. Type the IP Address/Domain name of the PC/server you want to ping the IP Address/ Domain Name.
  4. Click Start to diagnose.

What do the lights mean on a Dlink router?

Solid green A solid green light indicates an Internet connection. Blinking green A blinking green light indicates Internet activity. Solid red A solid red light indicates a PPP or DHCP failure. Check your username and password.

How do I know if my router is working properly?

To test if your router is working, try to ping one computer using another computer in the same network. You should be able to do this if the router is working properly. Your computer’s firewall must be disabled as well.

How do I find my router configuration page?

Find Your Router’s IP Address
You log into your router’s firmware through a browser. Any browser will do. At the address field, type the IP address of your router. Most routers use an address of 192.168.1.1.

How do I log into my 192.168 1.1 IP address?

How to Login 192.168. 1.1?

  1. Turn on your router and connect it to your computer with an Ethernet cable.
  2. Open your favorite web browser and type “http://192.168.1.1” into the address bar.
  3. Enter the correct router login/password combination.

How do I activate my Dlink router?

Setting up a D-Link Router

  1. Open the router in a new browser tab. Open your browser and navigate to http://192.168.0.1, the default IP address of the D-Link router.
  2. Enter the D-Link router password.
  3. Setup a strong password.
  4. Select your Timezone.
  5. Configure your internet connection.

What lights should be blinking on my router?

Internet (White / Amber) – The Internet LED is solid white when connected to the Internet. It blinks white while the router works to establish a connection. A solid amber LED indicates the connection is down due to configuration issues. Amber blinking indicates that the connection is down due to hardware issues.

What is the username and password for Dlink router?

The default user name for the D-Link DI-624 wireless router is “admin,” and the Password field should be left blank.

Why is my D-Link router flashing green?

The WPS LED or the Wi-Fi LED on your router should start to flash. Step 3: Press and hold the WPS button on the extender for 2-3 seconds. The LED should start to blink green. Once it makes connection with your router the LED will stop flashing and turn solid GREEN.

Why is my D-Link blinking?

If your D-Link router has a continually flashing “Power” button, you may have run into a hardware problem with one of a few different causes. The hardware itself may be bad, you may have interrupted the router in the middle of a firmware update or the router could just need to be reset.

How do I troubleshoot my D-Link wireless router?

How to Troubleshoot D-Link Wireless Router Quickly?

  1. Remove the D-Link router from the current position.
  2. Unplug any Bluetooth device or 2.4Hz cordless phone.
  3. Unfold a paper clip and push it into the rest hole of the D-link Router and hold it for 10 seconds.
  4. Open any web browser and enter 192.168.

How do you test a router?

1) Connect power to the router under test and let it boot. 2) Go to the LAN-side computer plugged into one of the router LAN ports. Unless you set the computer to use a static IP address, it will have grabbed a new IP address from the router’s DHCP server.

What are the symptoms of a bad router?

The 11 most common Signs of a Bad Router:

  • Login Problems.
  • Sudden Stoppage.
  • Dropped Performance or Slow Connections.
  • Non-Responsiveness.
  • Faulty Indicator Lights.
  • Reconnecting Continuously.
  • Bad Port or Wireless Failure.
  • Router Age.

Is it my router or my internet?

Connect to the router (with a web browser – it’s address is your computer’s gateway address) and do a speed test (most routers have a speed test utility). If you’re getting slow speed, it’s your router or your connection – call your internet provider. If you’re getting good speed in the router, it’s your WiFi setup.

How do you set up wifi?

To change Wi-Fi settings, tap All Networks.
Turn on & connect

  1. Open your device’s Settings app.
  2. Tap Network & internet. Internet.
  3. Tap a listed network. Networks that require a password have a Lock .

How do I find my Dlink IP address?

Press the Windows key and R together. Type cmd in the box and click OK. At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and default gateway of your adapter.

How do I log into my router admin panel?

Step 1: Open your web browser and type in the IP address of the router (192.168. 0.1 by default). Step 2: Enter the username (admin) and password (blank by default), and then click OK or Log In.

What is my IP address for my router?

How to find the IP address of your router using Windows

  • Right-click the Windows icon in the bottom-left of your screen, and select “Command Prompt.”
  • In the Command Prompt window, type “IPCONFIG” and press Enter.
  • Find the “Default Gateway” section. The number listed here is your router’s IP address.