For Windows 10
- Search for “Bluetooth” in your Windows search box.
- Once the Bluetooth & other devices window pops up, ensure Bluetooth is “on”
- Tap “Add Bluetooth or other device” and then select your device from the list. They will appear as ‘X2’.
- If you are prompted for a passcode, enter “0000”
Contents
How do I put my jaybirds in pairing mode?
Make sure your earbuds are off. Press and hold the right multifunction button for 6 seconds until you see the LED flashing green. When the LED flashes green, the earbud is in pairing mode. A voice prompt will say “Go to Bluetooth settings and select Jaybird RUN”.
How do I reset my Jaybird X2?
To reset your X2, you will get the headset into pairing mode (green and red alternating lights). Once in pairing mode press and hold both volume buttons for 3 seconds. X2 light will indicate the headset is reset by flashing yellow three times. Your headphones are now reset.
How do I set my earbuds to pairing mode?
Overview: How to Pair Bluetooth Earbuds
- Removing the earbuds from the charging case.
- Pressing and holding the power button.
- Opening the charging case.
- Removing the earbuds from the charging case and putting them back in.
- Pressing the pairing button on the charging case.
- Pressing the pairing button on the earbuds.
Why is my Jaybird not connecting?
If your buds are not responding, connect the charging clip and USB cable to a power source. This will turn your buds off and perform a soft reset.
How do I pair my Jaybird Vista 2?
Place both earbuds into the charging case and close the lid. Open the charging case and press and hold the case button until the three LEDs start blinking white. On your Bluetooth audio device, go to Bluetooth settings and ensure Bluetooth is enabled. Select ‘Jaybird Vista 2‘ in the list of discovered devices.
How do I factory reset my jaybird?
To reset your buds, follow the steps below.
- Make sure your buds are powered off.
- From an off state, press and hold the power button for 8 seconds until the LEDs flash red and green.
- Double press the power button. The LED will flash rapidly and you should hear a double tone. Your buds have now been reset.
Why is my Bluetooth not pairing?
For Android phones, go to Settings > System > Advanced> Reset Options > Reset Wi-fi, mobile & Bluetooth. For iOS and iPadOS device, you’ll have to unpair all of your devices (go to Setting > Bluetooth, select the info icon and and choose Forget This Device for each device) then restart your phone or tablet.
How do I pair my earbuds to my phone?
How to Connect Bluetooth Headphones to Android Phone
- First Open Settings.
- Next, tap Connections.
- Then tap Bluetooth.
- Then tap Scan at the top-right corner of your screen.
- Next, press and hold the power button on your headphones.
- Finally, find your headphones and tap them.
How do I turn my Bluetooth to discovery mode?
Android: Open the Settings screen and tap the Bluetooth option under Wireless & networks. Windows: Open the Control Panel and click “Add a device” under Devices and Printers. You’ll see discoverable Bluetooth devices near you.
Why is my Jaybird flashing red?
If your LED is not functioning correctly, please try a factory reset.Turn your X4 earbuds off by holding the Middle Button until the LED illuminates red and then goes off. 2. When your earbuds are powered off, press and hold the Middle Button for 5 seconds until the LED starts blinking green/red.
How do I reset my Jaybird Vista 2?
Complete a factory reset of your earbuds
Press and hold the case button until the three LEDs start blinking white. While the charge case LEDs are blinking white, press the case button twice. The LEDs will blink pink and you can now close the case. When you open the case, your earbuds are reset and ready to pair.
How do you set up Bluetooth?
Step 1: Pair a Bluetooth accessory
- Swipe down from the top of the screen.
- Touch and hold Bluetooth .
- Tap Pair new device. If you don’t find Pair new device, check under “Available devices” or tap More. Refresh.
- Tap the name of the Bluetooth device you want to pair with your device.
- Follow any on-screen instructions.
How do I pair my jaybird to my IPAD?
Here’s how to complete this process:
- Turn your Tarah earbuds on by holding the middle button until the LED blinks white and you hear the “Ready to pair.
- On your Bluetooth audio device go to the Bluetooth set up menu and find ‘Jaybird Tarah’ on the available devices list.
- Select ‘Jaybird Tarah’ on the list to connect.
How do I connect my Jaybird 2 to my Iphone?
With your headphones turned off, press and hold the Power Button until you see the LED flashing red/green. When the LED flashes red/green, the headphones are ready to pair. A voice prompt will say “Searching for your music device”. Select “Jaybird FREEDOM 2” in the list of discovered devices to connect.
Is there an app for Jaybird X2?
The Jaybird App gives you the tools you need to take total control of your Jaybird headphones. Create your own EQ presets and save them to your buds. Find a flawless fit.The app’s Find My Buds feature lets you track down missing buds.
How do I pair my Jaybird X3?
With your buds turned off, press and hold the Power Button until you see the LED flashing red/green. When the LED flashes red/green, the buds are ready to pair. A voice prompt will say “Searching for your music device”. Select “Jaybird X3” in the list of discovered devices to connect.
How do I open my Jaybird X2?
To open, gently apply pressure to the soft silicon with your thumb until the edge of the lid is revealed.
How do I make my Jaybird Vista discoverable?
Place both earbuds into the charging case and close the lid. Open the charging case and press and hold the case button until the case LED starts blinking white. On your Bluetooth® audio device, go to Bluetooth settings and ensure Bluetooth is enabled. Select ‘Jaybird Vista‘ in the list of discovered devices.
Can Jaybird Vista connect to two devices?
Your Jaybird Vista earbuds come out of the box ready to pair and can remember the pairing information for up to 8 devices. If you’re trying to pair an additional phone or audio device, you’ll need to manually initiate pairing mode on your earbuds: Place both earbuds into the charging case and close the lid.
How do I factory reset my Jaybird Vista?
Complete a factory reset of your earbuds
Press and hold the case button until the case LED starts blinking white. While the charge case LED is blinking white, press the case button twice. The LED will blink pink and you can now close the case. When you open the case, your earbuds are reset and ready to pair.