How To Label A Graph X Vs Y?

The proper form for a graph title is “y-axis variable vs. x-axis variable.” For example, if you were comparing the the amount of fertilizer to how much a plant grew, the amount of fertilizer would be the independent, or x-axis variable and the growth would be the dependent, or y-axis variable.

Contents

Do you plot y vs X or X vs Y?

In graphing jargon, the independent variable is plotted on the x-axis and the dependent variable is plotted on the y-axis. In any data set, the independent or X-variable is the one that was chosen or manipulated by the experimenter.

Does the X or Y variable come first?

When we prepare a graph the independent variable is always on the “x-axis”, and the dependent variable is always on the “y-axis”. We indicate which variable is which by saying as a function of or “versus”, with the dependent variable coming first, and the independent variable coming second.

How do you compare graphs?

How to ‘compare’ graphs. In questions where you are asked to compare, you need to comment on both the similarities and differences. For example, to compare the graph in Figure 1 with the graph in Figure 2 you would say that as both independent variables increase so does the rate of photosynthesis.

How do you label a graph in a lab report?

A graph should be labeled as a Figure, not a Table. The title of the figure should include enough detail that the image could “stand alone” without having to read too much of the paper.

How do you describe graphs and charts?

Describing language of a graph

  • UP: increase / rise / grow / went up / soar / double / multiply / climb / exceed /
  • DOWN: decrease / drop / fall / decline / plummet / halve / depreciate / plunge.
  • UP & DOWN: fluctuate / undulated / dip /
  • SAME: stable (stabilised) / levelled off / remained constant or steady / consistent.

How do you describe a plot graph?

A line graph plots data in a single line over time. To describe the graph, follow it’s progress along the horizontal access and describe whether it goes down, up, or stays the same.

How do you decide which graph to use?

Bar graphs are used to compare things between different groups or to track changes over time. However, when trying to measure change over time, bar graphs are best when the changes are larger.

What are axis labels on a graph?

Axis labels are words or numbers that mark the different portions of the axis. Value axis labels are computed based on the data displayed in the chart. Category axis labels are taken from the category headings entered in the chart’s data range. Axis titles are words or phrases that describe the entire axis.

How do you label a bar graph?

Required bar graph titles include the name of the graph, the title of the vertical axes, and the title of the horizontal axes. It is important to title bar graphs carefully so the information makes sense and the graph is easy to read and understand.

How do I label the y-axis in Google Sheets?

Change axis titles & tick marks

  1. On your computer, open a spreadsheet in Google Sheets.
  2. Double-click the chart you want to change.
  3. At the right, click Customize.
  4. Click Chart & axis title.
  5. Next to “Type,” choose which title you want to change.
  6. Under “Title text,” enter a title.
  7. Make changes to the title and font.

How do you describe a graph that goes up and down?

Small changes up and down are called ‘fluctuations’. We can describe this graph as follows: The revenues increase slightly over the first quarter (January to March) while there is a developing loss. Between March and April revenues increase significantly and there is a profit to correspond with this.

How do you present a graph in a report?

All graphs, diagrams and images should be titled as Figures. These will be numbered consecutively throughout the dissertation: Figure 1, Figure 2, Figure 3, and so on. After the numbering, there should be a short and concise title. Titles for figures appear below the figure itself.

How do you write a description of a bar graph?

1. How to choose information from the bar graph?

  1. One sentence for the introduction.
  2. Two sentences using superlatives.
  3. A sentence with a comparison.
  4. A sentence grouping two data points to show similarity (for example, you might include a brief description showing a gradual decrease in two different areas).

In which direction should the y-axis run?

Reminder: the x-axis really runs left and right, and the y-axis runs up and down.

What type of chart will you use to compare?

Bar and column charts are used to compare different items. Bars on a column chart are vertical while bars on a bar chart are horizontal. Bar charts are generally used to help avoid clutter when one data label is long or if you have more than 10 items to compare.

Which chart is used for variable inspection?

Variables control charts are used to evaluate variation in a process where the measurement is a variable–i.e. the variable can be measured on a continuous scale (e.g. height, weight, length, concentration).

How do you label a axis?

Click the chart, and then click the Chart Layout tab. Under Labels, click Axis Titles, point to the axis that you want to add titles to, and then click the option that you want. Select the text in the Axis Title box, and then type an axis title.

How do you label a graph?

The proper form for a graph title is “y-axis variable vs. x-axis variable.” For example, if you were comparing the the amount of fertilizer to how much a plant grew, the amount of fertilizer would be the independent, or x-axis variable and the growth would be the dependent, or y-axis variable.

What is label in a bar graph?

Bar charts are useful because they show data clearly. They must contain the following information: A title explaining what the bar chart means. Labels that tell you what each bar means. This could be a key or just a label underneath the line that runs along the bottom of the bar graph (the horizontal axis).

How do you label a line graph in Excel?

In Microsoft Excel, right-click on the data point on the far right side of the line and select Add Data Label. Then, right-click on that same data point again and select Format Data Label. In the Label Contains section, place a check mark in either the Series Name or Category Name box.