One of many reasons for ATA/SATA hard drives not detecting in BIOS could be the improper power supply and thereby hard drive not making a spin. A glitch in power or spin can easily be detected by following specific steps: Switch off the computer. Remove data cable from the hard drive.
Contents
Why is my SATA drive not showing up?
If your internal hard drive is not showing up, it might be because it is not initialized or it needs formatting. Make sure your disk is properly connected to the motherboard with the SATA cable. Your HDD might also not be visible in Windows 10 due to some BIOS settings.
How do I enable SATA drive?
To Set the System BIOS and Configure Your Disks for Intel SATA or RAID
- Power on the system.
- Press the F2 key at the Sun logo screen to enter the BIOS Setup menu.
- In the BIOS Utility dialog, select Advanced -> IDE Configuration.
- In the IDE Configuration menu, select Configure SATA as and press Enter.
How do I fix SATA port not detected?
Quick Fix 1. Connect ATA/SATA Hard Drive with Another Cable Port
- Reconnect the hard drive with the data cable port or connect ATA/SATA hard drive to another new data cable in PC;
- Connect the hard drive with another desktop/laptop as a second HDD;
What do I do if my internal hard drive is not detected?
To check to see if this is the cause of the BIOS not detecting the hard drive, follow these steps:
- Power off the computer.
- Open the computer case and remove the data cable from the hard drive. This will stop any power saving commands from being sent.
- Turn on the system. Check to see if the hard drive is spinning.
What is SATA mode in BIOS?
The SATA Mode BIOS feature is similar to the SATA Operation Mode BIOS feature, but with different options available. It controls the SATA controller’s operating mode.When set to RAID, the SATA controller enables both its RAID and AHCI functions. You will be allowed to access the RAID setup utility at boot time.
How do I change SATA mode to BIOS?
In the BIOS Setup utility, use the Right Arrow key to select the Storage tab. Use the Down Arrow key to select Storage Options, and then press Enter. Next to Sata Emulation, select the controller mode you want, and then press F10 to accept the change.
Why is my SSD not showing in BIOS?
The BIOS will not detect a SSD if the data cable is damaged or the connection is incorrect.Be sure to check your SATA cables are tightly connected to the SATA port connection. The easiest way to test a cable is to replace it with another cable. If the problem persists, then the cable was not the cause of the problem.
How do I identify my SATA port on my motherboard?
Check your motherboard. Near the SATA ports it should say “SATA 6G” or “SATA 3G”. If you don’t want to go with the Hardware method you can use a software called HWiNFO . When you open it you will see this exact window as the image above.
How do I know if my hard drive is detected in BIOS?
During startup, hold F2 to enter the BIOS Setup screen. Check whether your hard drive is listed under Bootable Device. If your hard drive isn’t listed, this indicates that there are no bootable system files on the hard drive.
What does no hard drive detected mean?
When a computer starts up with a message like hard drive not detected, no boot device found, no boot partition found, missing operating system, hard disk drive failure, etc. It means the computer is unable to find the default hard drive it uses when it loads.
How do you fix a hard drive failure?
How to Fix Hard Drive Failure
- Clean Out the Computer Vents. Over time, dust and debris will visibly clog up the vents on your computer.
- Check the Power and Data Cables. Your hard drive has power and data cables that connect to it from the computer power supply and motherboard.
- Check Your Bios.
- Listen for Sounds.
Does it matter which SATA port I use for boot drive?
SATA ports are numbered starting from 0. As far as the performance goes, it does not matter which port number you use (as long as they all belong to the same version as discussed earlier). However for the sake of consistency, generally, it is preferred that the first port i.e Port number 0, be used for the boot drive.
What SATA mode should I use for SSD?
So, if you are using a SATA SSD or HDD, you can set up the mode to utilize the advantages of the SATA interface. With the emergency of NVMe, more and more SSDs are designed with the NVMe protocol. Many hardware and SSD manufacturers recommend that AHCI mode can be used for SSD drives.
How do I set SATA to AHCI mode?
In UEFI or BIOS, find SATA settings to select the mode for memory devices. Switch them to AHCI, save settings and restart the computer. After the restart, Windows will start installation of SATA drivers, and when it is over, it will ask you for another restart. Do it, and AHCI mode in Windows will be enabled.
What is SATA mode AHCI or IDE?
AHCI and IDE are two modes in which a hard drive communicates with the rest of the computer system using a SATA storage controller.AHCI stands for Advanced Host Controller Interface and is a faster mode of operation compared to IDE. RAID mode also enables and makes use of AHCI.
What is SATA controller?
A SATA controller (serial ATA controller) is a hardware interface that connects a hard drive to a computer’s motherboard and manages or directs the flow of data.Advanced Host Controller Interface (AHCI) enables the use of advanced features, such as hot swapping, on SATA drives.
How do I fix an undetected SSD?
Quick Fix. Unplug and Re-plug SATA Data Cable on SSD
- Unplug SATA data cable on SSD, leave the power cable connected.
- Turn on the PC and boot into BIOS.
- Let PC sit idle in BIOS for about half an hour and turn off PC.
- Plug the SATA data cable back into SSD and turn on PC to boot into BIOS.
How do I know if my SSD is detected?
SOLUTION – Detecting the drive in the BIOS: In most cases the SSD will be automatically detected by the BIOS. In some cases the BIOS will display the drive model number while in other cases it will only indicate the existence of a drive and its capacity.
Do SSD drives use SATA cables?
To install the SSD as a secondary drive (not your primary or boot drive), use a SATA cable and attach one end of the cable to the SATA connector on your motherboard.Then, use an available SATA power cable coming from your system’s power supply and connect the cable to your Crucial SSD.
Where do SATA cables go?
SATA uses simple cables that are keyed to fit on the drive and motherboard connector one way. Connect one end of the SATA cable to the drive, and the other end to an available SATA port on your motherboard, and you’re halfway there.