when troubleshooting a router, you want to identify which other devices are connected to the router, as well as the subnet addresses of each connected subnet.
Contents
Which of the following documents would likely identify that drop cables on your network use the T568A standard?
Which of the following documents would likely identify that drop cables on your network use the T568A standard? Wiring schematic.
Which type of documentation would you consult to find the location of rj45 wall jacks and their endpoints in the intermediate distribution closet?
Which type of documentation would you consult to find the location of RJ-45 wall jacks and their endpoints in the intermediate distribution closet? Wiring schematic. You are concerned about the amount of traffic that passed through a router on your network.
When you run the software you only see frames addressed to the workstation not to other devices?
When you run the software, you only see frames addressed to the four workstations but not to the router. Which feature should you configure? Mirroring.
Which tool should you use to test the drop cable and the connection to the network?
Use a cable tester to test the cable between the computer system and the network switch.
What key advantage does a virtual router have?
The key advantage of a virtual router is that it can support multiple networks on a single router interface. It does this by using a different routing table for each network.
What is the purpose of using Ethernet bonding?
When Ethernet bonding is used, the bandwidth from two network interface cards (NICs) is combined, thus increasing the amount of bandwidth available for data transfers.
Which of the following protocols would you use for remote management?
The primary remote access protocols in use today are the Serial Line Internet Protocol (SLIP), Point-to-Point Protocol (PPP), Point-to-Point Protocol over Ethernet (PPPoE), Point-to-Point Tunneling Protocol (PPTP), Remote Access Services (RAS), and Remote Desktop Protocol (RDP).
Which of the following are requirements of the 1000baset Ethernet standards?
Fiber optics
Name | Standard | # Lanes (→) |
---|---|---|
1000BASE‑CX | 802.3z-1998 (CL39) | 4 |
1000BASE‑KX | 802.3ap-2007 (CL70) | 4 |
1000BASE‑SX | 802.3z-1998 (CL38) | 1 |
1000BASE‑LSX | proprietary (non IEEE) | 1 |
Which of the following networking devices or services prevents in most cases the use of IPsec as a VPN tunneling protocol?
confidentiality. Which of the following networking devices or services prevents the use of IPsec in most cases? firewalls, routers, and switches. A group of salesmen in your organization would like to access your private network through the internet while they are traveling.
Which of the following controls is an example of a physical access control method?
Locks on doors is an example of a physical access control method. Physical controls restrict or control physical access. Passwords, access control lists, and smartcards are all examples of technical controls. Even though the smartcard is a physical object, the card by itself is part of a technical implementation.
Which of the following devices is capable of detecting and responding to security threats?
Which of the following devices is capable of detecting and responding to security threats? intrusion prevention system (IPS) can detect and respond to security events. An IPS differs from an IDS because it can respond to security threats, not just detect them.
Which of the following tools would you use to view the MAC addresses associated with IP addresses?
The arp utility will show you the resolved MAC to IP address of all hosts on your network segment.
What tool can we use to test a network cable?
A cable tester is an electronic device used to verify the electrical connections in a signal cable or other wired assembly. Basic cable testers are continuity testers that verify the existence of a conductive path between ends of the cable, and verify the correct wiring of connectors on the cable.
How do you test Internet cable?
To test the cable, plug it into an ethernet cable tester and see if it successfully transmits a signal. If you don’t have a cable tester, there are a number of other troubleshooting tests to tell if the problem is the cable or your modem.
What tool is tested most cable wiring?
The Best Network Cable Testers
- ELEGIANT Cable Tester.
- iMBAPrice Network Cable Tester.
- Klein Tools LAN Explorer Data Cable Tester.
- Optimal Shop Network Cable Tester.
- Zoostliss Network Cable Tester.
- Noyafa Multi-functional Network Cable Tester.
- TRENDnet Network Cable Tester.
- Southwire Tools & Equipment Network Cable Tester.
How do I monitor and filter VM to VM traffic?
You want to be able to monitor and filter VM-to VM traffic within a virtual network.
- Implement a virtual firewall within a hypervisor.
- Route VM-to VM traffic through a physical firewall and back to the virtual network.
- Create a virtual router with VRF technology.
- Define VLAN memberships on each VM.
What tool would you use to grab and lift small objects?
Tongs are a type of tool used to grip and lift objects instead of holding them directly with hands.
Which of the following best describe OSPF?
Which of the following best describes OSPF?OSPF is a classless link state routing protocol.
What is bonding router?
Bonding Routers combine multiple ADSL or Broadband lines together to provide your network with one big fat internet connection. For example, if you have two ADSL Broadband connections each running at 10Mbps downstream, 1Mbps upstream, then the bonded performance will be up to 20Mbps downstream, 2Mbps upstream.
What is a bonded network?
Network bonding is a process of combing or joining two or more network interfaces together into a single interface. Network bonding offers performance improvements and redundancy by increasing the network throughput and bandwidth.Two or more network interfaces can be connected into a single logical “bonded” interface.