Check if the optical disc drive is dirty or broken. Dust is always the culprit for most DVD player not read/load errors.DVD player not working might be a sign that the disc tray, tray motor or laser is worn out. To fix any of the DVD hardware, you need to open the housing and check the inside with special tools.
Contents
Why is my DVD player not reading discs?
The most likely and common causes include: The DVD disc isn’t placed properly. The disc is dirty, damaged or burned in player-incompatible format. DVD player firmware issue.
Why is my DVD player not working on my TV?
Ensure the video cable between the DVD player and TV is securely connected to both devices.NOTE: If the issue only occurs with the first DVD, then the disc may have dust, fingerprints or scratches. Ensure the TV and DVD player are set to utilize the same type of video signal, either progressive or interlaced .
How do I get my DVD player to work?
How to Connect a DVD Player to a TV
- Unplug your TV and DVD player.
- Set the DVD player on a shelf near the TV.
- Connect your DVD player with the included cables.
- Whichever cable you use, plug one end into the DVD player, and the other into the corresponding port in the TV.
Why is my DVD player stuck on loading?
Possible Reasons & Fixes to DVD Player Loading Problem
If the DVD player is not loading all discs, then there could be dirty or bad lens and mainboard of the DVD player.Try another disc, if dvd player stuck on loading problem doesn’t happen with another disc, check if the problematic disc is dirty or scratched.
How do you reset a DVD player?
On the DVD remote control, press the UP ARROW or DOWN ARROW button to select the SETUP icon. Press the ENTER button. Press the UP ARROW or DOWN ARROW button to select RESET . Press the ENTER button.
What channel should TV be on for DVD player?
DVD players will display on one of the Input or Auxiliary channels. They will not show up on Channel 3 or 4 like some VCRs. Some TVs will label the Input channels based on the type of input, such as “HDMI”, “AV”, and “COMPONENT.” Refer back to Method one if you have a question about which input type you are using.
Why does my TV say no signal when I plug in my DVD player?
If your TV has the correct INPUT or Source, unplug the cable and plug it back, or try another cable or port. Sometimes cable can short-out.Test if your DVD player works on other TVs. It could be your DVD player breakdown that leads to No Signal on your HDTV.
How do you clean a DVD disc?
Mix rubbing alcohol and water in a one-to-one ratio and use it to clean the DVD to remove fingerprints or other oily residue. Rubbing alcohol works well because it is mild and evaporates quickly without leaving a residue. Rub the disk with a little of the solution and let it dry.
Why is my DVD player playing in black and white?
This issue can occur if a video signal encrypted with copyright protection passes through a VCR. If using A/V cables, check that the red, white, and yellow plugs are securely connected to the same colored jacks on both the disc player and TV (or A/V receiver).
How do I connect my DVD player to my HDMI TV?
Step 1: Plug the HDMI cable into the Blu-ray or DVD player. Step 2: Plug the opposite end of the HDMI cable into the HDMI port on your TV. Step 3: That’s it! Make sure to select the correct input on your TV to connect with your player.
Why is my Sony DVD player not working?
Reset your Sony DVD player. Unplug it from the power source for 10 minutes or longer, and then plug it back in.Then, you need to try cleaning the laser lens inside the Sony DVD player with a cleaning disc. Or you can open the unit and wipe the glass laser head gently with an alcohol-infused eyeglass cleaner wipe.
How do I reboot a DVD without a remote?
If you can’t find your DVD player or Blu-ray player remote control, or it has stopped working, don’t despair. You can often still play media using buttons on the device itself. You can also use a universal remote or, with some models, a smart phone app to control the player.
If the DVD player fails to operate, try to reset the unit by switching it off and removing the plug from the wall. Wait a minute and then restart the DVD player.
How do you watch a DVD on a TV?
How to Play a DVD on a Television Set
- Connect the video and audio outputs of the DVD player to the video and audio inputs of the television set using the RCA video cables.
- Plug the DVD and TV into power sources if you have not done so already and power both devices on.
- Set the TV to the proper video channel.
How can I play a DVD on my TV without a DVD player?
So if you have your titles on disc that you want to play on your TV set without DVD player, USB drive is a great option. You can convert your DVDs and put them on a USB drive with a good DVD to video converter.
Why does my TV say no signal when HDMI is plugged in?
Verify that the source device has power and is turned on. If the source device is connected with an HDMI® cable: Make sure the TV and source device are both turned on, then disconnect the HDMI cable from one of the devices and then connect it again.Try a new or another known working HDMI cable.
Why is the TV saying no signal?
A “No Signal”, “No Source”, or “No Input” message will appear on your TV screen if the TV is not receiving a signal from your TV box. This is often a result of either the TV box being powered off, not being properly connected to the TV, or the TV being set to the wrong input.
How do you fix the TV when it says no signal?
Reset the box
- Turn everything off at the wall.
- Check that all cables are securely and firmly in place.
- Wait for 60 seconds.
- Plug your TV box (not the television set) in and turn it on.
- Wait another 60 seconds, or until the lights on the TV box have stopped flashing.
- Plug everything else back in and turn it all back on.
Can you use vinegar to clean DVDs?
Wipe the disc with a cloth that has been dampened with white vinegar. The acetic acid in vinegar cuts through the oils left behind by your fingers, as well as any other dirt and grime that might be on the disc. Start at the center and wipe straight out to the edge of the disc to avoid damaging the disc.
Can you wash a DVD with soap and water?
Wipe across the disc rather than in a circular motion, which can cause microscratches and damage the data stored on the disc. If that doesn’t do the job, dampen the cloth with a gentle soap-and-water solution and rewipe. Never use household cleaners, abrasives or solvents on CDs or DVDs.